Flytech FLY-POS797IR Manual de usuario

USER MANUALPoint-of-SaleHardware SystemVERSION V1.4 DECEMBER 2010

32System View2. Front View2-1. Side View2-2. 345Fanless System Fan SystemItem No. Description1 Touch Screen2 MSR Module (Optional)3 External Antenna (

4Rear View with stand2-3. 6789Fan SystemFanless SystemRear View without wall mount bracket2-4. 1110Fan SystemFanless SystemItem No. Description6 VFD (

5I/O Ports View2-5. a bcd e f gh ijFanless Systema bcd e f gh ijFan SystemItem No. Descriptiona Parallelb USB x 4c COM 1, 2, 3, 4 (from right to left)

6System Dimension2-6. 386 mm308 mm220 mm370 mm 62 mm250 mm80 °411 mm390 mm 220 mm407 mm63 mm250 mm80 °15" System 17" System

7System Assembly3. Turn to the rear side of the system.1. Unscrew the screw (x1) securing 2. the HDD door and the rear cover of the system.Disconnect

8Removing a RAM modulePlease Open the rear cover by 1. unfasten the screws (x17) to access the motherboard.Use both fingers to pull the ejector 2. cli

9Power Adapter Replacement3-4. Disconnect the power cable from 1. the adapter pre-installed in the power bracket attached in the stand.Unscrew the scr

10Peripheral Installation4. MSR Installation4-1. Unfasten the thumb screws (x2) to 1. remove the I/O cover.Connect the MSR module into the 2. system a

11Wall Mount Kit Assembly4-3. Fix the metal bracket (a) to the 1. VESA bracket and the display with the screw (b) (x1).Align the tear drop holes of th

12afbdecDesktop Stand Assembly4-4. VESA bracket assemblyAlign the standard VESA mounting 1. holes of the VESA bracket (a) and the display and fix them

iiCopyright 2010All Rights ReservedManual Version 1.4Part Number: 3LMPP7900214The information contained in this document is subject to change without

13Wireless LAN Installation4-5. Disconnect the HDD cable from the 1. system first (see Chapter 3-1).Unscrew the screws (x17) to 2. remove the rear cov

14cdbaOpen the rear cover by removing 1. the screws (x17)Fix the antenna mounting bracket 2. (b) with the screw (x1) onto the LCD chassis under the re

15SSD Card Replacement4-6. On a Fan System4-6-1. If your system equipped with SSD Card instead of hard drive disk as storage device, please follow bel

16On a Fanless System4-6-2. 1. Follow 4-6-1 step 1 to assemble SSD module. 2. Turn to the rear side and open the rear cover on a fanless system (see

17Cash Drawer Installation 4-7. For B78 motherboard4-7-1. You can install a cash drawer through the cash drawer port. Please verify the pin assignment

18Bit 7: Reserved.Bit 6: Reserved.Bit 5: Reserved.Bit 4: Cash Drawer “DIN bit0” pin input status. = 1: the Cash Drawer closed or no Cash Drawer.

19For B68/B98/C48 motherboard4-7-2. You can install a cash drawer through the cash drawer port. Please verify the pin assignment before installation.B

20Bit 7: ReservedBit 6: Cash Drawer “DIN bit0” pin input status. = 1: the Cash Drawer closed or no Cash Drawer = 0: the Cash Drawer openedBit 5: Res

21Motherboard B68 B78 B98 C48Fan/Fanless Fanless FanlessFan(performance)Fan (Performance)FanlessCPU SupportIntel Atom N270 processors 1.6G (BGA)Intel

22Motherboard B68 B78 B98 C48Cash Drawer Port 1 x RJ 11 (12V /19V)Audio Jack 1 x Line-out, 1 x Mic-inAudioBuilt in Speaker N/A N/A 2x2W 2x2W N/APower

iiiCE MARKThis device complies with the requirements of the EEC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 200

23Version: B68 v1.0For B68 Motherboard6-1. Jumper Setting6. Motherboard Layout6-1-1.

24Connector PurposeBAT1 CMOS Battery Base ( Use CR2023)CN1 Power On ButtonCN2 Touch SensorCN3 Power LEDCN4 SATA1 HDD Power ConnectorCN5 SATA2 HDD Powe

25Connector PurposeSATA2 SATA ConnectorSKT1 SPI ROMUSB1 USB1, USB2USB2 USB3, USB4SW1 Power On BottomJP1 CRT ConnectorJP2 CRT Power/I2C ConnectorJP3 CO

26COM2 RS232/485/422 SettingFunction JP6 JP5▲RS2328 105 7 921 3645 7 9 1121 36 8 10 124RS4858 105 7 92136411128 105 7 921 364RS4228 105 7 921 364105 7

27Cash Drawer Power SettingFunction JP11▲+12V21 34 +19V21 34Power Mode SettingFunction JP9 ▲ATX Power21 AT Power 21RTC ResetFunction JP8 ▲CMOS N

28LCD ID SettingPanel# ResolutionLVDSOutputInterfaceJP7Bits Channel1 1366 x 768 24 SingleLVDS Panel85 721 3642 1440 x 900 24 DualLVDS Panel85 721 3644

29Version: B78 v2.2For B78 Motherboard6-2. Motherboard Layout6-2-1.

30Connectors & Functions6-2-2. Connector PurposeBAT1 CMOS Battery Base ( Use CR2023)CN1 Audio Line OutCN2 Audio MIC InCN3 Internal Power SwitchCN4

31Jumper Setting6-2-3. COM2 RS232/485/422 SettingFunction JP10 JP9▲RS23211128 105 7 921 3645 7 921 36 8 104RS4855 7 9 1121 36 8 10 1248 105 7 921364RS

32Cash Drawer Power SettingFunction JP4▲+12V521 364 +19V521 364Power Mode SettingFunction JP6 ▲ATX Power21 AT Power 21CMOS Operation ModeFunctio

ivLEGISLATION AND WEEE SYMBOL2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal o

33LCD ID SettingPanel# ResolutionLVDSJP7Bits Channel1 640 x 480 18 Single85 721 3642 800 x 600 18 Single85 721 3643 1024 x 768 18 Single85 721 3644 12

34Version: B98 v1.0For B98 Motherboard6-3. Motherboard Layout6-3-1.

35Connectors & Functions6-3-2. Connector PurposeBAT3 CMOS Battery Base (Use CR2023)CN3 Audio Line OutCN4 MIC InCN5 Internal Power On Switch Connec

36Jumper Setting6-3-3. COM2 RS232/485/422 SettingFunction JP6 JP4▲RS2325 7 9 1121 36 8 10 1245 7 921 36 8 104RS48511128 105 7 921 3645 7 921 36 8 104R

37Cash Drawer Power SettingFunction JP3▲+12V 521 364 +19V521 364Power Mode SettingFunction JP11 ▲ATX Power21 AT Power 21CMOS Operation ModeFunct

38LCD ID SettingPanel# ResolutionLVDSOutputInterfaceJP8Bits Channel1 1366 x 768 24 SingleLVDS Panel85 721 3642 1440 x 900 24 DualLVDS Panel85 721 3644

39Version: C48 v2.1For C48 Motherboard6-4. Motherboard Layout6-4-1.

40Connector PurposeCN1 Power Button ConnectorCN3 Printer Port ResetCN4 Printer PortCN5/8 HDD PowerCN11 COM5 For TouchCN13 Card Reader ConnectorCN14 Li

41COM2 RS232/485/422 SettingFunction JP5 JP4▲RS2321 3 5 7 92 6 8 1045 7 9 1121 36 8 10 124RS4858 105 7 92136411128 105 7 921 364RS4228 105 7 921 36410

42System IndicatorFunction JP10 ▲Disable85 721 364Enable85 721 364Inverter SelectionFunction JP14▲ CCFL LEDCMOS Operation ModeCMOS ResetTo clear the

vRevision HistoryChanges to the original user manual are listed below:Revision Description Date1.0 Initial release• 2007 August1.1Cover page update•

43COM3 & COM4 Power SettingFor C48, COM3/COM4 power adjustment must be made by BIOS/Utility and Jumper. Since COM3/COM4 default is “None“ m

44LCD ID SettingSeveral congurations are applied to different sizes of panel. Please refer to the followings to complete relevant settings. 12.1&quo

454. To switch on the power, select "+12V". Please save the change before exiting BIOS to avoid data lost.5. To switch brightness level, s

46Appendix: Drivers InstallationThe shipping package includes a Driver CD in which you can nd every individual driver and utility that enables you to

viTable of Contents1. Packing List ... 11-1. Standard Accessories ...11-2. Op

vii4-6. SSD Card Replacement ...154-6-1. On a Fan System ...

1Packing List1. Standard Accessories1-1. a.b.c.d.e.f.System (with stand)a. Driver bankb. User guidec. Power adapterd. Power corde. RJ45-DB9 cable (x2)

2Optional Accessories1-2. a.b.c.d.e.Metal MSRa. Metal VFDb. Wall-mount Kitc. SSD moduled. WLAN Card (with internal antenna)e. abc